Floating shelves are very useful equipment to put showpieces and other essential equipment. Use floating shelves in our bathroom to put shampoo, lotion, towel, etc. In our kitchen, we use this self to keep our spices, pans, plants, and other necessary tools.
But there is one disadvantage of using shelves on the wall, and that is it requires too many holes on the wall. While growing up we all have seen some holes in our room. But now thanks to the technology, the shelves don’t require any drills or holes anymore. The floating shelves allow this to be hung without causing any damage to the wall. That’s correct, we’re talking about screwless shelves!
Using drills is sometimes risky as well. So many people did not gather the courage to use it. But by knowing How to install floating shelves without brackets anyone can install the shelves without any need to call professionals.
Here we would recommend and provide guidelines of some very easy steps to install floating shelves at home. So stay with us and learn those steps carefully. Checking the Wall Mounted Shelves will be helpful as well.
Steps to Install Floating Shelves without Brackets
Materials and Tools Needed
No matter what project you are on, you have to collect all the equipment beforehand. This will make the work process simpler and easier. So for installing floating shelves you will need the following equipment
- Finish Nailer
- Miter Saw
- Table Saw
- Sand Paper
- Wood Filler
- Tape Measurer
- Wood Glue
- Wood Stain
- Finish Nails
Step 1: Set the Location
It is critical to plan the placement of your shelves. You do realize you need to prepare the area where you’ll install your shelf, don’t you? So, before you install the anchors and plugs, decide where you’re going to put your shelf.
Do you have your tools on hand? Take out the stud finder and pencil from your bag. Mark the placement of the wall studs using a pencil. When you’re finished, draw straight lines for each of our shelves. fix a level to the wall. For more suggestions, you can read about Sandpaper for Glass.
Step 2: Take the Measurements
The first thing you must decide is how many shelves you require or desire. This is primarily determined by the amount of vertical space available. According to the measure you have to purchase the wood. The space where we installed the shelves in our bathroom extended all the way from the floor to the ceiling. So we have got 12 feet of vertical area to play with. However, you definitely do not want to set your first shelf too low. And it looks good when you are placing 2 to 3 shelves in a line. Remember you are leaving much space between the shelves, otherwise, if the shelf is lower you will be in trouble. For example, if you want to keep a 700ml shampoo bottle on the shelf, this won’t fit. So keeping all things in mind, do the measurement process.
Step 3: Buy a Lightweight material
To hang heavy boards made of dense, hard materials like oak or steel, nail clippers are required. However, the self-adhesive caps can be used to attach lightweight hollow boards like wood waltzes. As a general rule, try hanging shelves weighing no more than 1.4 kg.
If the boards weigh more than 4.5 kg, do not hang them on tape for security reasons. Choose a hollow floating shelf from a fittings store or a light-colored wood shelf from a home improvement store.
Step 4: Sand the board
Standing is essential for all types of wood. Sanding makes the board more smooth and provides a Shiny finish. You can dye the open shelves after they’ve been installed. But standing before installing the board will give you the freedom to move the Sandpaper the way you want to. That way, you won’t have to worry about staining the walls. Then wiped the stain off with a clean rag. The boards were then totally dry before sanding with a fine sanding block. Then I added a satin polyurethane coat.
Step 5: Cut the woods
As by now you have bought the woods, it is time to cut it according to the measurements you have taken before. Before using a saw to cut the piece of wood, make sure it fits inside the length of the shelf.
Step 6: Attach the stripes
Do not forget to clean the wall properly before attaching the strips. Use a rag to remove all of the dust before. Then Hold the Velcro fastening sides with the two mounting Brackets or straps if not already attached.
Separate the protective layer from one of the tapes, then apply the newly exposed adhesive to the shelf mounting spot and press the sticky strips together for approximately 30 seconds. Repeat the procedure with the remaining films.
Spread the strips equally to ensure that your shelf hangs as well as possible. To hold the shelf to the wall without using screws, attach the strips on the wood planks with staples.
Step 7: Attach the board
After fixing the adhesive tapes, peel out all of the leftover linings from the tape and position the shelf against the wall. Then, for about 30 seconds, press the shelf against the wall to secure it in place. Tape the two sides and the shelf with duct tape and hang them at an angle if possible. It will strengthen the shelf. To lift the shelf away from the wall, slowly and carefully pull the shelf’s edges away from the wall. Divide each pair of pieces so that one side adheres to the shelf and the other to the wall. Allow about an hour for the tape to solidify. Then, using sticky tape, replace the shelf.
Once the shelves are attached properly, you are ready to place your favorite items on the shelf. It is better not to put any fragile items on the shelves especially when you have children. So now you know the whole procedure to install floating shelves without brackets. Try it on your own and share the idea with friends and family. If you are looking for the best display case for figures, you can check here.
I, Mike K. was born on August 25, 1992, in Abingdon Virginia. Our family relocated to Santa Monica, California after middle school.
I received an electrical engineering degree from U.C. San Francisco. While looking for work, he was guided by an engineering position at the company where he is working for. Besides working, David and I are started blogging about the latest developments of electrical stuff and enjoy sharing my thoughts with readers.