How to Make FM Antenna Booster – Easy Method Explained

If you get a very clear signal from your radio without an antenna booster then you are lucky, but in most cases, it is hard to get a strong network. Thus many people need to attach an FM antenna booster.  The radio reception can be poor for various reasons. FM radios sometimes have poor reception because their antenna is either too small for the station you’re attempting to reach or something is obscuring the signal. But the boost of the proper ratio can solve this problem.

Now you must be wondering where you can find a booster or how much it will cost. But don’t worry, you can make it all by yourself and the cost will be very low. Just following 3-4 steps anyone can learn how to make an FM antenna booster.

But before proceeding, let’s know what FM antenna booster is and what its purpose is.

Why Do You Need FM Antenna Booster

An FM antenna booster is a device that improves the reception of an FM antenna’s signal. Antenna booster significantly amplifies a radio signal for devices that receive radio waves. Many products, including mobile phones, radios, TVs, and Wi-Fi and Bluetooth devices, contain an RF amplifier stage in their circuitry that amplifies the antenna signal. Amplifiers magnify everything, both the desired signal and the noise present at the antenna.

It enables the FM radio receiver to use weak radio signals as though they were powerful. Or we can also say an FM antenna booster boosts your FM antenna’s reception power. In most circumstances, the weaker the signal, the further you are from a broadcasting station. As a result, if you are distant from the radio station, the signal reaching your antenna may be insufficient to create audible sound. To overcome this, an FM antenna booster will amplify the signal so that the antenna can pick it up. For more amazing products like this, check out our guide to the Mobile Scanner Antenna.

Ways of Making FM Antenna Booster

When listening to your favorite FM radio station, it may be incredibly aggravating when static or poor reception interferes with your enjoyment of the programming. but the connection can be fixed by making an FM Antenna Booster which is inexpensive and very easy to make. And following the inexpensive way to make antenna boosters you can access more radio stations while also improving the quality of their sound. Check out the most essential Review for Multiband HF Wire Antenna.

Tools Needed

You need to take all the necessary tools that are going to be needed during the process. Try to keep the following tools with you when you start working.

• Wire stripper
• Electrical tape
• Wire cutter
• Utility knife
• Screwdriver
• Measuring tape

Step 1:

The first thing you need to do is cut the wire. Take the wire cutter and cut the cable 7 feet from the spool of electric wire.  before cutting the weather major it with the measuring tape.

Then you have to take one end of the cut wire and remove the insulation.  try to cut the instigation up to half-inch in length. Make sure you also check our guide for Antenna for Uniden Scanner.

Step 2:

Strip the insulation between the two wires in the cable using a utility knife from the designated place with the electric tape all the way to the end of the cable. Do it from the covered end, not from the instigation cut end.

Then, along the 2.6-foot length, pull apart the two wires so that the entire 7.7-foot length forms a T shape. It is not necessary to utilize a 7.7-inch wire. Whatever length you choose, the ratio of the straight and branching parts must be 2:1. So keep this thing in mind. Besides, you can choose some Antenna Tuner.

Step 3:

It’s time to take the screwdriver. You need to start with losing the two screws that already have attached to the antenna. And after loosening the screws remove the wire. Connect one of the bare ends of the cable to the end of one of the two wires that connect to the FM antenna through the screws. Repeat the procedure for the second antenna wire and the other exposed end of the cable. Additionally, you can check our review on Handheld Scanner Antenna.

Step 4:

Attach each of the sets of wires, and here the sets of the antenna mean the original antenna wire and the cable.  After that back to each of the screws at the junction, attach them, and tighten the screws back down. And finally, tape the ends of the cable to the desired location.

Final Words

A lot of people are afraid of making a payment in a booster because they think this is a very hard task. But now you know how simple and easy it is to make FM antenna boosters for having a more stable and clear connection.  so without during start working on your radio antenna if you feel the signal is weak, and get the strongest signal on your own. Have a great day!